Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2010 Ford Ranger car and truck
repair procedures including Ford engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2010 Ford Ranger automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2010 Ford Ranger
- 2010 Ford Ranger XL 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2010 Ford Ranger XL 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:D
- 2010 Ford Ranger XLT 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
- 2010 Ford Ranger XLT 2.3 L4 GAS, CID:140, Fuel Injection, Aspiration:140, Engine VIN:, Desg:D
- 2010 Ford Ranger Sport 4.0 V6 GAS, CID:245, Fuel Injection, Aspiration:245, Engine VIN:, Desg:E
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2010 Ford Ranger XLT 4.0 V6 GAS
Front
- Raise and support the vehicle.
- Index-mark front driveshaft to front axle flange and at transfer case flange.
- Remove and discard bolts and U-joint retainers.
- Remove and discard flange bolts.
- Compress and separate front driveshaft from front axle, then separate driveshaft from transfer case. Wrap electrical tape around the bearing cups to prevent them from falling off the U-joint spider.
- Reverse procedure to install, noting the following:
- Tighten transfer case flange bolts in a cross pattern.
- Torque flange bolts to 22 ft. lbs.
- Torque U-joint retainer bolts to 15 ft. lbs.
Rear
- Raise...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2010 Ford Ranger XLT 2.3 L4 GAS
Front
- With vehicle in NEUTRAL, position it on a hoist.
- Remove front wheel and tire assembly.
- Remove and discard the hub nut and washer assembly.
- Remove front disc brake caliper, anchor plate and pads as an assembly, and position assembly aside.
- Remove brake disc.
- Separate outboard front wheel halfshaft joint from wheel hub.
- Support front suspension lower arm.
- Remove nut and bolt retaining upper ball joint to front wheel knuckle.
- Remove outboard front wheel halfshaft joint...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2010 Ford Ranger Sport 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2010 Ford Ranger XL 4.0 V6 GAS
Front
- With vehicle in NEUTRAL, position it on a hoist.
- Remove front wheel and tire assembly.
- Remove and discard the hub nut and washer assembly.
- Remove front disc brake caliper, anchor plate and pads as an assembly, and position assembly aside.
- Remove brake disc.
- Separate outboard front wheel halfshaft joint from wheel hub.
- Support front suspension lower arm.
- Remove nut and bolt retaining upper ball joint to front wheel knuckle.
- Remove outboard front wheel halfshaft joint...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front
Vehicle: 2010 Ford Ranger XLT 4.0 V6 GAS
Front
- With vehicle in NEUTRAL, position it on a hoist.
- Remove front wheel and tire assembly.
- Remove and discard the hub nut and washer assembly.
- Remove front disc brake caliper, anchor plate and pads as an assembly, and position assembly aside.
- Remove brake disc.
- Separate outboard front wheel halfshaft joint from wheel hub.
- Support front suspension lower arm.
- Remove nut and bolt retaining upper ball joint to front wheel knuckle.
- Remove outboard front wheel halfshaft joint...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2010 Ford Ranger AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2010 Ford Ranger cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble -> Single Cardan, Flange Yoke -> Single Cardan, Slip Yoke
Vehicle: 2010 Ford Ranger XL 4.0 V6 GAS
Single Cardan, Slip Yoke
Disassemble
Do not, under any circumstance, clamp the shaft in the jaws of a vise or similar holding fixture. Denting or localizing fracture can result, causing shaft failure during vehicle operation. Place the shaft on a suitable workbench. Do not damage the tube. If components are not marked and installed incorrectly, driveline imbalance can occur.
- Index-mark the shaft components.
- Remove and discard all four snap rings.
- Clamp bearing cup removal tool No. 205-086 or equivalent in a vise.
- If necessary, use a pair of pliers to remove a bearing cup t...
CLICK HERE TO GET FULL ACCESS TO 2010 Ford Ranger DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
