Auto Parts Search
Dodge Caliber CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Dodge REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Year
2010 | 2009 | 2008 | 2007 |

BRAKE SERVICE PROCEDURES FOR Dodge Caliber AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported Dodge Caliber cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Replacement -> Caliber, Avenger & Sebring Sedan -> Challenger -> Charger, Magnum & 300 -> Crossfire -> Except Caliber, Avenger & Sebring Sedan -> Fluid Reservoir -> Hydraulic Control Unit -> Junction Block -> Master Cylinder -> Proportioning Valve -> With ABS -> Without ABS
Vehicle: 2009 Dodge Caliber R/T 2.4 L4 GAS
Fluid Reservoir
Caliber, Avenger & Sebring Sedan
- Clean master cylinder housing and brake fluid reservoir.
- Remove brake fluid reservoir cap, then siphon as much brake fluid as possible from reservoir.
- Remove reservoir to master cylinder mounting screws.
- Pull reservoir straight up to remove from master cylinder.
- Remove brake fluid switch from reservoir.
- Reverse procedure to install.
Except Caliber, Avenger & Sebring Sedan
These models use ISO style flares that are of metric dimension. Use ISO style tubing flares and metric tubing when performing any repairs.
- Remove reservoir caps.
- Remo...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported Dodge Caliber cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2009 Dodge Caliber SE 2.0 L4 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove cotter pin, nut lock, spring washer, and hub nut from end of outer C/V joint stub axle.
- Disconnect front wheel speed sensor and secure harness aside.
- Remove nut and bolt retaining ball joint stud into steering knuckle.
- Separate ball joint stud from steering knuckle by prying...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR Dodge Caliber AUTOMOBILES
Description, component locations, reset procedures, relearn procedures, diagnosis and testing, wiring diagrams, component replacement, and identification of vehicles equipped and not equipped with tire pressure monitoring system for most domestic and imported Dodge Caliber cars and light trucks sold in the U.S. from mid 1990's+.
Relearn Procedures
Vehicle: 2008 Dodge Caliber SXT 1.8 L4 GAS
When a tire pressure sensor has been replaced, the WCM will learn and store the sensor ID when the vehicle is driven continuously above 15 mph for 10 minutes. A new sensor ID can also be programmed directly into the WCM using a suitably ...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR Dodge Caliber AUTOMOBILES
Includes starter and alternator replacement procedures for domestic and imported Dodge Caliber cars and light trucks from 1990+.
Starter, Replace
Vehicle: 2008 Dodge Caliber SE 2.0 L4 GAS
- Disconnect battery ground cable.
- Remove air cleaner box and air tube.
- Remove starter motor mounting bolts.
- Disconnect electrical connector at throttle body.
- Remove throttle body mounting bolts, then throttle body.
- Push starter under intake manifold.
- Tip starter nose...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR Dodge Caliber AUTOMOBILES
Cabin air filter locations and replacement procedures with corresponding images for most domestic and imported Dodge Caliber cars and light trucks sold in the U.S. as equipped to the current model year.
Cabin Air Filter Service -> Chrysler LLC -> 2007-09 Caliber
Vehicle: 2007 Dodge Caliber SE 1.8 L4 GAS
The cabin air filter should be replaced every 12,000 miles.
- Open the glove compartment.
- Disengage the glove compartment bin dampener from the bin.
- Push inward on the sides of the glove compartment bin to release the stops, then lower the glove compartment.
- Release the glove compartment hinge pins from the hinge retainers, then remove the glove compartment, Fig. .
- Release the two tabs retaining the cabin air filter cover to the A/C-heater housing, then remove the cover, Fig. .
- Remove the cabin air filter element from the A/C-heater ...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR Dodge Caliber AUTOMOBILES
Maintenance lamp reset procedures with corresponding images for most domestic and imported Dodge Caliber cars and light trucks sold in the U.S. from 1990+.
Chrysler LLC Cars -> Anti-Lock Brake System (ABS) Warning Lamp -> 2007-09 Caliber
Vehicle: 2007 Dodge Caliber SE 1.8 L4 GAS
This lamp should light when the ignition is turned On. The lamp may light for as long as 30 seconds as a bulb and system inspection. If the lamp remains lit or lights while operating the vehicle, a fault condition in the anti-lock brake system is indicated. When the lamp is lit, turn ignition Off, then start the engine again. If the lamp still remains lit, the anti-lock brake system should be serviced. The brake system will ...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR Dodge Caliber AUTOMOBILES
Includes radiator, cooling and heater hose replacement procedures for domestic and imported Dodge Caliber cars and light trucks from 1990+
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2010 Dodge Caliber SXT 1.8 L4 GAS
Lower
- Drain coolant into a suitable container.
- Loosen hose clamp connecting hose to radiator.
- Loosen hose clamp connecting hose to water pump inlet tube.
- Remove hose from vehicle.
- Reverse procedure...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR Dodge Caliber AUTOMOBILES
Serpentine belt replacement procedures with corresponding images for most domestic and imported Dodge Caliber cars and light trucks sold in the U.S. from 1990+.
Serpentine Drive Belt, Replace
Vehicle: 2008 Dodge Caliber SXT 2.0 L4 GAS
- Rotate accessory drive belt tensioner counterclockwise until accessory drive belt...
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR Dodge Caliber AUTOMOBILES
Component location diagrams for most Dodge Caliber cars and light trucks sold in the U.S. from 1990+.
![]() Components on diagram: |
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR Dodge Caliber AUTOMOBILES
OEM drawn wiring diagrams for most Dodge Caliber cars and light trucks sold in the U.S.
![]() Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR Dodge Caliber AUTOMOBILES
OEM TSB listings for most Dodge Caliber cars and light trucks sold in the U.S. from 1985+.
Document: RADIO SPEAKER MISDIAGNOSIS - RATTLE / BUZZ SOUNDS IN DOOR MODULES Vehicle: 2007 Dodge Caliber SXT 2.0 L4 GAS Symptoms: |
Document: CONTINUOUSLY VARIABLE TRANSMISSION (CVT) AUTOMATIC SHIFTER DIAGNOSTICS Vehicle: 2007 Dodge Caliber SE 2.0 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR Dodge Caliber AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO Dodge Caliber SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
![]() |
Access the Complete guide! |