Auto Parts Search
2008 Dodge Caliber CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Dodge REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Brake Service
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Dodge Caliber car and truck
repair procedures including Dodge engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Dodge Caliber automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Hydraulic Brake Systems -> Hydraulic Brake System Specifications
Vehicle: 2008 Dodge Caliber SE 1.8 L4 GAS
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber BRAKE SERVICE PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 2008 Dodge Caliber SE 1.8 L4 GAS
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Drain differential carrier oil into suitable container.
- Mark rear propeller shaft and differential, Fig. , for proper installation.
- Remove rear propeller shaft to rear axle retaining nuts.
- Remove three bolts from center support heat shield, then heat shield.
- Remove center support mount...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Component Replacement -> Installation -> Removal -> Tire Pressure Sensor -> Tire Pressure Transponder
Vehicle: 2008 Dodge Caliber SXT 1.8 L4 GAS
Tire Pressure Sensor
The cap used on this valve stem contains an O-ring seal to prevent contamination and moisture from entering the valve stem. Retain this valve stem cap for reuse. Do not substitute a regular valve stem cap in its place.
The valve stem used on this vehicle is made of aluminum and the core is nickel plated brass. The original valve stem core must be reinstalled and not substituted with a valve stem core made of a different material. This is required to prevent corrosion in the valve stem caused by the different metals.
Removal
- Loosen the wheel lug nuts.
- Raise...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Alternator, Replace
Vehicle: 2008 Dodge Caliber SE 2.0 L4 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Remove right front wheel.
- Remove underbody air dam.
- Remove accessory drive splash shield.
- Rotate or lift belt tensioner arm, using a suitable tool to relieve tension from drive belt.
- Remove drive belt.
- Remove accessory drive idler pulley.
- Loosen lower mounting bolt.
- Loosen A/C compressor and relocate, pull down and to outboard side of vehicle.
- Unplug field circuit ...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Cabin Air Filter Service -> Chrysler LLC -> 2007-09 Caliber
Vehicle: 2008 Dodge Caliber SE 1.8 L4 GAS
The cabin air filter should be replaced every 12,000 miles.
- Open the glove compartment.
- Disengage the glove compartment bin dampener from the bin.
- Push inward on the sides of the glove compartment bin to release the stops, then lower the glove compartment.
- Release the glove compartment hinge pins from the hinge retainers, then remove the glove compartment, Fig. .
- Release the two tabs retaining the cabin air filter cover to the A/C-heater housing, then remove the cover, Fig. .
- Remove the cabin air filter element from the A/C-heater ...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Chrysler LLC Cars -> Air Bag Warning Lamp ->
Vehicle: 2008 Dodge Caliber SE 2.0 L4 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned On as a bulb check. If the Air B...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Radiator, Replace
Vehicle: 2008 Dodge Caliber SE 1.8 L4 GAS
- Drain engine coolant into suitable container.
- Remove radiator core support.
- Disconnect upper radiator hose from radiator.
- Remove wiring harness bracket.
- Disconnect radiator fan electrical connector.
- Remove radiator fan mounting screws.
- Detach radiator fan assembly from retaining clips.
- Remov...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Dodge Caliber R/T 2.4 L4 GAS
- Rotate accessory drive belt tensioner counterclockwise until accessory drive belt...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Dodge Caliber AUTOMOBILES
Component location diagrams for most 2008 Dodge Caliber cars and light trucks sold in the U.S. from 1990+.
 Door Diagram for 2008 Dodge Caliber R/T 2.4 L4 GASComponents on diagram: |
 Front Body Components Diagram for 2008 Dodge Caliber SE 1.8 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Dodge Caliber AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Dodge Caliber cars and light trucks sold in the U.S.
 2008 Dodge Caliber SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
 2008 Dodge Caliber SE 2.0 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Dodge Caliber AUTOMOBILES
OEM TSB listings for most 2008 Dodge Caliber cars and light trucks sold in the U.S. from 1985+.
|
Document: Poor Handling and/or Strut Leaking and/or Rides Rough Vehicle: 2008 Dodge Caliber R/T 2.4 L4 GAS Symptoms: |
|
Document: RECALL - Emissions Recall J19 California Emissions Warranty Addendum Vehicle: 2008 Dodge Caliber R/T 2.4 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Dodge Caliber AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Dodge Caliber cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Dodge Caliber vehicle.
|
| Access the Complete guide! |
