Auto Parts Search
We have info for following modifications of 2008 Dodge Caliber
- 2008 Dodge Caliber R/T 2.4 L4 GAS, CC:2360, CID:144, Fuel Injection, Aspiration:144, Engine VIN:, Desg:K
- 2008 Dodge Caliber SXT 1.8 L4 GAS, CC:1798, CID:110, Fuel Injection, Aspiration:110, Engine VIN:, Desg:C
- 2008 Dodge Caliber SXT 2.0 L4 GAS, CC:1998, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:B
- 2008 Dodge Caliber SE 1.8 L4 GAS, CC:1798, CID:110, Fuel Injection, Aspiration:110, Engine VIN:, Desg:C
- 2008 Dodge Caliber SE 2.0 L4 GAS, CC:1998, CID:122, Fuel Injection, Aspiration:122, Engine VIN:, Desg:B
- 2008 Dodge Caliber SRT-4 2.4 L4 GAS, CC:2360, CID:144, Fuel Injection, Aspiration:144, Engine VIN:, Desg:F
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Dodge Caliber SXT 1.8 L4 GAS
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Drain differential carrier oil into suitable container.
- Mark rear propeller shaft and differential, Fig. , for proper installation.
- Remove rear propeller shaft to rear axle retaining nuts.
- Remove three bolts from center support heat shield, then heat shield.
- Remove center support mount...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Caliber SXT 2.0 L4 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove cotter pin, nut lock, spring washer, and hub nut from end of outer C/V joint stub axle.
- Disconnect front wheel speed sensor and secure harness aside.
- Remove nut and bolt retaining ball joint stud into steering knuckle.
- Separate ball joint stud from steering knuckle by prying...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Caliber SE 2.0 L4 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove cotter pin, nut lock, spring washer, and hub nut from end of outer C/V joint stub axle.
- Disconnect front wheel speed sensor and secure harness aside.
- Remove nut and bolt retaining ball joint stud into steering knuckle.
- Separate ball joint stud from steering knuckle by prying...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Caliber SXT 1.8 L4 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove cotter pin, nut lock, spring washer, and hub nut from end of outer C/V joint stub axle.
- Disconnect front wheel speed sensor and secure harness aside.
- Remove nut and bolt retaining ball joint stud into steering knuckle.
- Separate ball joint stud from steering knuckle by prying...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 2008 Dodge Caliber SE 1.8 L4 GAS
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Drain differential carrier oil into suitable container.
- Mark rear propeller shaft and differential, Fig. , for proper installation.
- Remove rear propeller shaft to rear axle retaining nuts.
- Remove three bolts from center support heat shield, then heat shield.
- Remove center support mount...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Dodge Caliber AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Dodge Caliber cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2008 Dodge Caliber R/T 2.4 L4 GAS
Front
Halfshaft inner and outer boots are not serviceable separately. Boot replacement requires entire shaft assembly replacement.
Lefthand halfshaft is shorter than right. Identify and tag halfshafts upon removal to ensure proper installation.
- Raise and support vehicle.
- Remove tire and wheel assembly.
- Remove cotter pin, nut lock, spring washer, and hub nut from end of outer C/V joint stub axle.
- Disconnect front wheel speed sensor and secure harness aside.
- Remove nut and bolt retaining ball joint stud into steering knuckle.
- Separate ball joint stud from steering knuckle by prying...
CLICK HERE TO GET FULL ACCESS TO 2008 Dodge Caliber DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Dodge Caliber vehicle. |
Access the Complete guide! |