Auto Parts Search
1993 BMW 325IC CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT BMW REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1993 BMW 325IC car and truck
repair procedures including BMW engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your BMW 325IC automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Imported Cars & Light Trucks & Vans -> 1993-95 -> System Inspection -> Compressor -> Condenser -> Evaporator -> Receiver/Drier -> Refrigerant Line Restrictions -> Thermostatic Expansion Valve
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
While a detailed diagnostic procedure for all air conditioning systems would be impractical due to the many variations in construction and operation, there are three fundamental components of a total diagnosis:
- Refrigerant systems must have an adequate, but not excessive charge.
- Determination must be made whether the refrigerant system is governed by a cycling clutch compressor or by valves which control evaporator pressure.
- The air distribution system (blower motor, switches, vacuum lines and air ducts) must be operational before checking the refrigera...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Hydraulic Brake Systems -> Brake System Bleed
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
- Connect suitable pressure bleeder to brake fluid reservoir. Maximum charging pressure is 43.5 psi.
- Attach bleeder hose and container to right rear wheel. Bleed until no bubbles appear.
- Repeat step 2 for left rear, right front and left front wheels.
- Support rear suspension at wheel carriers and lower car so rear suspension compresses to its normal loaded position (to prevent damage to output shaft joints). Wheels must be able to turn freely.
- Attach...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
BMW -> Fuel Filter Replacement -> Except X3 & Z4 -> Fuel System Pressure Relief -> Models w/Fitting Or Union Bolt Connection -> Models w/Fuel Hose Connection -> Removal & Installation
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
After the battery has been disconnected and reconnected, some abnormal driveability symptoms may occur. The vehicle may need to be driven while it relearns its adaptive strategy.
Fuel System Pressure Relief
- Obtain the vehicle owner's radio theft protection code.
- Remove the fuel pump relay(s).
- Start the engine and allow it to stall.
- Crank engine for 10 seconds to ensure the fuel pressure has been...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
DRIVESHAFT, Replace -> With constant velocity joint -> With slide
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
With slide
- Raise and support vehicle.
- Remove complete exhaust system.
- Remove heat shield.
- Unscrew holders for exhaust suspension.
- Remove clamp.
- On models with joint disk, unscrew joint disk on transmission.
- On models with universal joint, unscrew universal joint on transmission.
- Release threaded bushing with special tool 26 1 040 or equivalent by a few turns.
- Caution: When removing propeller shaft, mark universal joint to drive flange of rear axle. This will eliminate complaints of droning.
- Unscrew universal joint on final drive.
- On all models, Unscrew center bearing.
- Kink propeller sha...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Starter, Replace
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
- Disconnect battery ground cable, then remove air cleaner assembly.
- Disconnect throttle cable, then remove air grill of air collection box.
- Remove electric lead duct...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Cabin Air Filter Service -> BMW -> 1992-98 3 Series
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
Service interval is determined by the service indicator.
- Obtain the radio anti-theft code prior to disconnecting the battery ground cable.
- Disconnect the battery ground cable.
- On all models except convertible, disengage the two air nozzles (located above the glove compartment) at the top. Position the nozzles straight ahead, then remove the nozzles.
- On all models, remove the glove compartment retaining screws located at each side. On convertible models, the upper two screws are accessed through the air nozzle opening.
- Disconnect the glove compartment lamp.
- Remove the two lower glove ...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
BMW -> Automatic Stability Control (ASC, ASC+) & Dynamic Stability Control (DSC) Warning Lamp ->
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
The warning lamp is used to warn of a system fault. It will be lit during engine start-up, but should go out when the self-diagnostic system determines that the system is functioning properly. The warning lamp will also flash when the syst...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
Inlet
- Drain coolant into a suitable container.
- Reposition hose clamp at heater core and remove hose.
- Reposition hose clamp at coolant outlet and remove hose.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1993 BMW 325IC AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1993 BMW 325IC 2.5 L6 GAS
- Remove fan cowl by lifting out expansion rivets on both sides.
- Secure fan pulley with suitable securing tool, or equivalent, then remove fan. Fan has lefthand handed threads.
- Loosen tensioner lock bolts, then turn tensioner with suitable wrench to receive tens...
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1993 BMW 325IC AUTOMOBILES
Component location diagrams for most 1993 BMW 325IC cars and light trucks sold in the U.S. from 1990+.
 LH Front Wheel Above Brake Caliper Diagram for 1993 BMW 325IC 2.5 L6 GASComponents on diagram: |
 RH Rear Side Of Luggage Compartment Diagram for 1993 BMW 325IC 2.5 L6 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1993 BMW 325IC AUTOMOBILES
OEM drawn wiring diagrams for most 1993 BMW 325IC cars and light trucks sold in the U.S.
 1993 BMW 325IC 2.5 L6 GAS Wiring DiagramComponents on diagram: |
 1993 BMW 325IC 2.5 L6 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1993 BMW 325IC AUTOMOBILES
OEM TSB listings for most 1993 BMW 325IC cars and light trucks sold in the U.S. from 1985+.
|
Document: Tools and Equipment Vehicle: 1993 BMW 325IC 2.5 L6 GAS Auto Systems: |
|
Document: Diagnosis Feedback with ISTA Vehicle: 1993 BMW 325IC 2.5 L6 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1993 BMW 325IC AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1993 BMW 325IC cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1993 BMW 325IC cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1993 BMW 325IC cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1993 BMW 325IC cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1993 BMW 325IC SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1993 BMW 325IC vehicle.
|
| Access the Complete guide! |
