Auto Parts Search
We have info for following modifications of 1993 Saab 9000
- 1993 Saab 9000 Aero 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1993 Saab 9000 Aero 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:R
- 1993 Saab 9000 CD 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1993 Saab 9000 CD 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1993 Saab 9000 CDE 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1993 Saab 9000 CDE 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1993 Saab 9000 CS 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1993 Saab 9000 CS 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
- 1993 Saab 9000 CSE 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:B
- 1993 Saab 9000 CSE 2.3 L4 GAS, CC:2290, Fuel Injection, Engine VIN:, Desg:M
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Anti-lock Brakes -> Mark II Anti-Lock Brake System w/Traction Control -> Troubleshooting
Vehicle: 1993 Saab 9000 CDE 2.3 L4 GAS
- The diagnostic socket (green) is located below the righthand front seat.
- During fault diagnosis, the ignition switch must always be in the On position.
- The ISAT system number for the TC/ABS system is number 3.
- Always read off and note down all stored diagnostic trouble codes before disconnecting the battery or ECU.
- If communication cannot be established between ISAT and the ECU, check the leads between ECU pins 23 and 42 and the diagnostic socket. Also check that the power feed and ground circuits to the diagnostic socket are good and the connector pins are not damaged.
- Once diagnost...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Component Service -> Assemble -> Disassemble -> Master Cylinder Overhaul
Vehicle: 1993 Saab 9000 CD 2.3 L4 GAS
Master Cylinder Overhaul
When working on any hydraulic brake components it is extremely important to keep the work area clean. Clean any parts that are to be reused with new brake fluid or a cleaning fluid specifically designed for hydraulic components. Wipe all parts dry using clean lint-free paper or cloth. Gaskets, seals, O-rings and rubber components should not be reused. Prior to assembly, all components should be generously lubricated with clean brake fluid.
Disassemble
- Clamp master cylinder in soft-jaw vice.
- Remove rubber seals from brake hose connections.
- Carefully push pri...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> 1993 -> 1994-96 -> 1994-96 900 -> 900 -> 9000 -> 9000 & 1993 900 -> Caliper Overhaul -> Caliper, Replace -> Front -> Rear
Vehicle: 1993 Saab 9000 CSE 2.3 L4 GAS
Caliper, Replace
Front
900
- Remove brake pads as outlined previously.
- Loosen brake hose at caliper.
- Press brake pedal fully to floor and secure in that position.
- Remove upper guide pin bolt, then disconnect brake hose at caliper and plug hose and fitting.
- Remove caliper.
- Reverse procedure to install and bleed brake system.
9000
- Remove brake pads as outlined previously.
- Loosen brake hose at caliper.
- Press brake pedal fully to the floor and secure in that position.
- Disconnect brake hose at caliper and plug hose and fitting.
- Remove caliper.
- Reverse procedure to install. Bleed brake system.
Rear
900
1...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Disc Brakes -> Adjustments -> 1994-96 -> 900 -> 9000 -> Parking Brake -> Parking Brake Cable Equalization -> Parking Brake Shoes
Vehicle: 1993 Saab 9000 Aero 2.3 L4 GAS
Parking Brake
900
- Raise rear seat, then pry adjusting device apart.
- Insert a .08 inch feeler gauge between parking brake lever and stop on brake caliper.
- Screw locknut against adjusting sleeve until feeler gauge drops out.
- Apply and release parking brake lever a few times to settle adjusting device.
- Ensure clearance between lever and stop is .02-.08 inch.
- Lower rear seat.
9000
- Release parking brake.
- Remove screw plug from adjusting screw on back side of rear caliper, Fig. .
- Tighten adjusting screw, then back off 1/4- 1/2 turn. Ensure rotor turns freely.
- Ensure clearance between p...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Disc Brakes -> Caliper Service -> 1993 -> 1994-96 -> 1994-96 900 -> 900 -> 9000 -> 9000 & 1993 900 -> Caliper Overhaul -> Caliper, Replace -> Front -> Rear
Vehicle: 1993 Saab 9000 CD 2.3 L4 GAS
Caliper, Replace
Front
900
- Remove brake pads as outlined previously.
- Loosen brake hose at caliper.
- Press brake pedal fully to floor and secure in that position.
- Remove upper guide pin bolt, then disconnect brake hose at caliper and plug hose and fitting.
- Remove caliper.
- Reverse procedure to install and bleed brake system.
9000
- Remove brake pads as outlined previously.
- Loosen brake hose at caliper.
- Press brake pedal fully to the floor and secure in that position.
- Disconnect brake hose at caliper and plug hose and fitting.
- Remove caliper.
- Reverse procedure to install. Bleed brake system.
Rear
900
1...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1993 Saab 9000 AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1993 Saab 9000 cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> 1994-96 900 -> 9000 & 1993 900
Vehicle: 1993 Saab 9000 CD 2.3 L4 GAS
9000 & 1993 900
- Ensure brake fluid reservoir is full.
- Connect transparent hose to bleed nipple of brake caliper.
- Place other end of hose into clear container.
- Depress brake pedal, then open bleed nipple. Close nipple as soon as pedal reaches floor. Repeat this until no air bubbles are visible in fluid.
- Repeat previous step at each brake caliper, then refill fluid reservoir. On models with Anti-Lock Brake Systems (ABS), front calipers must be bled before rear calipers.
1994-96 900
- Unscrew cover of brake fluid reservoir and top off with brake fluid.
- Connect topping-off fitting fr...
CLICK HERE TO GET FULL ACCESS TO 1993 Saab 9000 BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1993 Saab 9000 vehicle. |
Access the Complete guide! |