Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1996 Suzuki X-90 car and truck
repair procedures including Suzuki engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1996 Suzuki X-90 automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Suzuki X-90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Suzuki X-90 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 1996 Suzuki X-90 JLX 1.6 L4 GAS
- Raise and support vehicle and remove wheel.
- Place a suitable container under transaxle and drain transaxle oil.
- Remove locking hub (if equipped).
- Remove drive shaft circlip.
- Remove stabilizer ball joint nut.
- Remove tie-rod end castle nut. Then disconnect tie-rod end from knuckle.
- Remove caliper bolts.
- Remove caliper from disc, and suspend with a wire hook.
- Remove knuckle ball joint stud nut.
- Support lower arm with jack.
- Remove knuckle from ball joint stud.
- Remove strut bracket bolts.
- Remove knuckle and wheel hub comp. by lowering jack. Right side: To detach snap ring fitted on spline...
CLICK HERE TO GET FULL ACCESS TO 1996 Suzuki X-90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Suzuki X-90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Suzuki X-90 cars and light trucks from 1990+.
DRIVESHAFT, Replace
Vehicle: 1996 Suzuki X-90 JLX 1.6 L4 GAS
- Raise and support vehicle.
- Drain transfer oil only when servicing front propeller shaft.
- Before removing propeller shaft, give match marks on joint flange and prop...
CLICK HERE TO GET FULL ACCESS TO 1996 Suzuki X-90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1996 Suzuki X-90 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 1996 Suzuki X-90 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Installation -> Removal
Vehicle: 1996 Suzuki X-90 JLX 1.6 L4 GAS
Removal
- Using special tool 09900-06108 or equivalent, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 3 - 4 mm (0.12 - 0.16 in.) from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in steps 2 and 3.
- Push out bearing race on flange yoke side as described in Steps 1 and 2, and then, holding bearing race in a vise, tap flange yoke and take out race...
CLICK HERE TO GET FULL ACCESS TO 1996 Suzuki X-90 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
