Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1998 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> Description -> AC-Delco Single Diaphragm Type -> AC-Delco Tandem Diaphragm Type -> Toyota/GM Single Diaphragm Type
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
AC-Delco Tandem Diaphragm Type
This unit utilizes a vacuum power chamber, consisting of a front and rear shell, housing divider, front and rear diaphragm, plate assemblies, hydraulic pushrod and a diaphragm return spring, Figs. and .
In normal operating mode, with service brakes in released position, the booster operates with vacuum on both sides of its diaphragms. When brakes are applied, air at atmospheric pressure is admitted to one side of each diaphragm to provide power assist. When the service brake is released, atmospheric air is shut off from one side of each diaphragm. The a...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> Precautions
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
- After disassembling a power brake unit, soak all metal parts in solvent.
- Use only alcohol on parts containing rubber. After the parts have been thoroughly cleaned and rinsed in solvent, they should be rewashed in clean alcohol before assembling.
- Use compressed air...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> Brake System Bleed -> Bleed Sequence -> Hydraulic System Flush -> Manual -> Pressure
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Manual
Pressure bleeding is recommended for all hydraulic systems. However, if a pressure bleeder is unavailable, use the following procedure. Brake fluid damages painted surfaces. Immediately clean any spilled fluid.
- Remove vacuum reserve by pumping brakes several times with engine off.
- Fill master cylinder reservoir with clean brake fluid. Do not let reservoir fall below half full during bleeding procedure.
- If necessary, bleed master cylinder as follows:
- Loosen master cylinder forward brake line connection until fluid flows from reservoir, then tighten brake line.
- Instruct an ass...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Anti-Lock Brakes -> Bosch Type 5 -> SYSTEM SERVICE -> 1997-98 Corvette -> 1997-98 DeVille, Eldorado, 1997 Seville, 1997-98 Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue & 1997-98 Regency -> Auto Bleed -> Brake Pressure Modulator Valve -> Brake System Bleed -> Component Replacement -> Electronic Brake Traction Control Module -> Front -> Hydraulic System Flush -> Manual Bleed -> Pressure Bleed -> Rear -> Wheel Speed Sensor
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Brake System Bleed
Auto Bleed
Perform manual or pressure bleeding as outlined under " Manual Bleed" or "Pressure Bleed" before auto bleeding system
- Turn ignition switch to Off position.
- Raise and support vehicle. remove all tire and wheel assemblies.
- Inspect brake system for leaks and damage. Repair as necessary.
- Connect suitable programmed scan tool to Data Link Connector (DLC) located on lefthand side of instrument panel below steering column.
- Turn ignition switch to On position. Do not start engine.
- Establish scan tool communications by selecting ABS/TCS, Special Functions and Automate Bl...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> General Service
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Two basic types of power assist mechanisms are used: vacuum assist diaphragm assemblies, which use engine vacuum or, in some cases vacuum pressure developed by an external vacuum pump. The second type is a hydraulic pressure assist mechanism, which use pressure developed by an external pump (usually the power steering pump). Both systems act to increase the force exerted on the master cylinder piston by the operator. This in turn increases the hydraulic pressure delivered to the wheel cylinders, while decreasing driver effort necessary to obtain acceptable stopping performance.
V...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1998 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Brake Pad Service -> Installation -> Removal
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Removal
- Remove brake caliper as described under "Caliper Service."
- Position suitable pliers over caliper and center of inboard shoe and lining, Fig. , then squeeze pliers to bottom pistons in caliper bores.
- Remove shoe and lining assemblies.
Installation
- Install inboard shoe and...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
