Auto Parts Search
1998 Chevrolet Corvette CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chevrolet REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
A/C & HEATER SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Air Bag System Precautions -> General Motors Corp. -> Arming -> Light Trucks & Vans -> Passenger Cars
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Passenger Cars
Reverse disarming procedures to arm the Supplemental Restraint System, noting the following:
- Ensure all disconnected SRS electrical connectors are securely connected and routed.
- Install all removed fuses in proper locations.
- From a safe position at sides of or below air bag module, Turn ignition switch to ON position and observe Air Bag or SRS warning lamp.
- On all models except Prizm and 1990 Corvette, warning lamp should flash seven to nine times, then go off.
- On Prizm models, warning lamp should light for six seconds,...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Description
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
This front caliper, Fig. , consists of dual pistons and an aluminum housing which is suspended on the shoe and lining assemblies. Hydraulic pressure, created by applying force to the brake pedal, acts equally against the pistons and the botto...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
General Motors Corp./Saturn Passenger Cars -> Component Locations -> 1997-03 Corvette
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Refer to Fi...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
DRIVESHAFT, Replace
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
- With transmission in neutral and parking brake released, raise and support vehicle, then remove underbody braces, as required.
- Remove exhaust system as follows:
- Disconnect AIR pipe from catalytic converter and exhaust pipe.
- Disconnect electrical connector to oxygen sensor.
- Remove bolts securing muffler to hangers, disconnect exhaust pipes from manifolds and remove exhaust system as an assembly.
- Support transmission, remove support beam retaining bolts and support beam.
- Mark position o...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Component Replacement -> Installation -> Removal -> Tire Pressure Indicator Sensor
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Tire Pressure Indicator Sensor
Removal
- Loosen the lug nuts.
- Raise and support vehicle with jack stands, then remove the wheel and tire assembly.
- Prior to dismounting the tire from the wheel, note the following precautions:
- Position the bead breaking fixture 90° from the valve stem when separating the tire bead from the wheel.
- Place the mounting and dismounting head so that the tire iron or pry bar can be inserted slightly clockwise of the sensor body when prying the tire bead up and over the head.
- Rotate the tire and wheel assembly clockwise using the tire changer when transferri...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Starter, Replace
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
- Disconnect battery ground cable.
- Raise and support vehicle.
- Disconnect HO2S connectors.
- Remove take down pipe flange nuts.
- Remove intermediate pipe to rear pipe attaching bolts.
- Remove front exhaust hanger bolts from take down pipe bracket.
- Remove rear exhaust hanger bolts from rear intermediate exhaust pipe.
- Remove intermediate pipe assembly.
- Remove rear HO2S from intermediate pipe...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
General Motors Corp./Saturn Cars -> Check Engine Or Service Now Soon Engine Indicator Lamps (Gasoline Engines w/Electronic Engine Controls Or EFI) -> Except LeMans, Metro, Prizm, Storm & Vibe
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
The Check Engine lamp should light when the ignition is turned On. When the engine is started, the lamp should go off. If the lamp remains on for 10 seconds or constantly after the engine is started, the self diagnosis system has detected a fault condition and has stored a code in the system Electronic Control Module (ECM) or Powertrain Control Module (PCM). After diagnosis and repair, the ECM memory can be cleared of codes as follows:
On models except Cadillac with DEFI, remove the ECM/PCM fuse or disconnect the battery ground cable for approximately 30...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator using hose clamp pliers.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from water pump housing using hose clamp pliers.
- Remove radiator outlet hose from water pump housing and from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1998 Chevrolet Corvette AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS
- Loosen accessory drive belt tensioners No. 3 and 10 in to reduce tension on accessory drive belts.
- Remove accessory drive belts.
- Clean accessory drive belt sur...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1998 Chevrolet Corvette AUTOMOBILES
Component location diagrams for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. from 1990+.
LH Rear Of Engine Diagram for 1998 Chevrolet Corvette 5.7 V8 GAS Components on diagram: |
Ground Distribution Diagram for 1998 Chevrolet Corvette 5.7 V8 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1998 Chevrolet Corvette AUTOMOBILES
OEM drawn wiring diagrams for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S.
1998 Chevrolet Corvette 5.7 V8 GAS Wiring Diagram Components on diagram: |
1998 Chevrolet Corvette 5.7 V8 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1998 Chevrolet Corvette AUTOMOBILES
OEM TSB listings for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. from 1985+.
Document: Revised General Motors New Vehicle Tire Warranty Program Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS Auto Systems: |
Document: New Website for AFIT, TPM, and VDR Updates Vehicle: 1998 Chevrolet Corvette 5.7 V8 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1998 Chevrolet Corvette AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1998 Chevrolet Corvette cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Corvette SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 1998 Chevrolet Corvette vehicle. |
Access the Complete guide! |