Auto Parts Search
1998 Chevrolet Metro CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Chevrolet REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Chevrolet Metro car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Chevrolet Metro automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
Component Replacement & Adjustment -> Metro & Prizm -> Control Assembly, Replace -> Metro -> Prizm
Vehicle: 1998 Chevrolet Metro LSI 1.3 L4 GAS
Metro
- Remove ash tray from receiver.
- Pull out glove compartment by pressing in on both side stoppers, then disconnect lighter connector.
- Remove four screws, then the center console trim bezel.
- Remove radio.
- Pull knobs out of control panel, then remove screw at lower right of instrument cluster.
- Pry out control panel face plate and disconnect illumination lamp.
- Remove A/C Switch if equipped.
- Disconnect control panel cables at heater case and blower case.
- Remove blower switch mounting screws, then pull control out of ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
Power Brake Units -> Adjustments -> AC-Delco Single Diaphragm Type -> AC-Delco Tandem Diaphragm Type -> Air Method -> Brake Pedal -> Gauge Method -> Pushrod -> Toyota/GM Single Diaphragm Type
Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS
Brake Pedal
Toyota/GM Single Diaphragm Type
- With engine running and brake pedal in rest position, measure distance between face of pedal and floor mat.
- If distance is not 5.79-6.18 inches, adjust pedal height as follows:
- Remove left lower instrument panel trim section and air duct.
- Loosen stop lamp switch sufficiently to gain clearance for pedal adjustment.
- Loosen locknut and rotate pedal pushrod as needed to obtain specified pedal height, then tighten locknut.
- Adjust position of brake light switch so that plunger lightly contacts pedal stopper and brake lamps are off when pedal is release...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
General Motors Corp./Saturn Passenger Cars -> Fuel Filter Replacement -> Vibe, 1998-02 Metro & Prizm
Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS
Do not smoke or allow an open flame of any type when working on or near any fuel system related components. The highly flammable vapor mixtures may ignite, resulting in serious personal injury.
Prior to disconnecting fuel lines, the fuel system pressure must be relieved to prevent acciden...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 1998 Chevrolet Metro LSI 1.3 L4 GAS
- Raise and support vehicle.
- Remove front tire and wheel assembly.
- Remove one bolt and ABS speed sensor from steering knuckle (if equipped).
- Unstake wheel drive shaft nut.
- Remove wheel drive shaft nut and washer.
- Remove ball stud bolt. Ball stud bolt is threaded into steering knuckle. Protect drive axle seals from sharp tools and from sharp edges of surrounding components. Any damage to seals or clamps, will result in leaking of joint lubricating grease from inner and outer joints; and entering of contaminates into inner and outer joints. This condition will lead to noisy drive ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
Alternator, Replace
Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS
- Disconnect battery ground cable.
- Remove air cleaner assembly.
- Remove rubber protector, nut and electrical connector from alternator B terminal.
- Remove upper mounting bolt.
- Remove drive belt.
- Remove two lower alt...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
General Motors Corp./Saturn Cars -> Air Bag Warning Lamp ->
Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS
This lamp should light for a approximately 6-8 seconds when the ignition is turned on as a bulb check. If the air b...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 1998 Chevrolet Metro LSI 1.3 L4 GAS
Lower
- Drain cooling system into a suitable container.
- Reposition hose clamp from radiator using hose clamp pliers.
- Remove radiator outlet hose from radiator.
- Reposition hose clamp from water pump housing using hose clamp pliers.
- Remove radiator outlet hose from water pump housing and from vehicle.
- Reverse procedu...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1998 Chevrolet Metro AUTOMOBILES
Serpentine Drive Belt, Replace -> A/C Compressor -> Alternator
Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS
A/C Compressor
- Raise and support the vehicle.
- Remove the right front wheel.
- Remove the six push clips and the lower splash shield at the right front side.
- Loosen the nut that retains the tension pulley, and loosen the tension bolt.
- Remove the A/C compressor drive ...
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1998 Chevrolet Metro AUTOMOBILES
Component location diagrams for most 1998 Chevrolet Metro cars and light trucks sold in the U.S. from 1990+.
 I/P Wiring Diagram for 1998 Chevrolet Metro LSI 1.3 L4 GASComponents on diagram: |
 Bulkhead Diagram for 1998 Chevrolet Metro LSI 1.3 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1998 Chevrolet Metro AUTOMOBILES
OEM drawn wiring diagrams for most 1998 Chevrolet Metro cars and light trucks sold in the U.S.
 1998 Chevrolet Metro 1.0 L3 GAS Wiring DiagramComponents on diagram: |
 1998 Chevrolet Metro 1.0 L3 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1998 Chevrolet Metro AUTOMOBILES
OEM TSB listings for most 1998 Chevrolet Metro cars and light trucks sold in the U.S. from 1985+.
|
Document: Revised General Motors New Vehicle Tire Warranty Program Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS Auto Systems: |
|
Document: New Website for AFIT, TPM, and VDR Updates Vehicle: 1998 Chevrolet Metro 1.0 L3 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1998 Chevrolet Metro AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1998 Chevrolet Metro cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1998 Chevrolet Metro cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1998 Chevrolet Metro cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1998 Chevrolet Metro cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1998 Chevrolet Metro SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
