Auto Parts Search
1998 Honda Prelude CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Honda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- A/C & Heater Service
- Brake Service
- Fuel Filter Replacement
- Driveline, U-Joint & CV Axles Replacement
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1998 Honda Prelude car and truck
repair procedures including Honda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Honda Prelude automobile. Try the Automotix DIY solution today!
A/C & HEATER SERVICE PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Imported Cars & Light Trucks & Vans -> 1998-2000 -> Evacuating System -> Using Charging Station -> Using Vacuum Pump
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
Using Vacuum Pump
Vacuum pumps suitable for removing air and moisture from A/C systems are commercially available. A specification for system pump down used here is 28-291/2 inches vacuum. This reading can be attained at or near sea level only. For each 1000 feet of altitude this operation is performed, the reading will be 1 inch vacuum higher. For example, at 5000 feet elevation, only 23-241/2 inches of vacuum can be obtained. The system refrigerant must be completely recovered before it can be evacuated. Damage to the vacuum pump will result if pressurized ...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude A/C & HEATER SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Disc Brakes -> Parking Brake Service -> Adjustment
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
Adjustment
Refer to...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude BRAKE SERVICE PROCEDURES
FUEL FILTER REPLACEMENT PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Honda -> Fuel Filter Replacement -> del Sol, 1985-91 CR-X, 1985-01 Prelude, 1985-97 Accord, 1987-00 Civic, 1997-01 CR-V & 1995-97 Odyssey w/Fuel Injected Engines -> Fuel System Pressure Relief -> Removal & Installation
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
Fuel System Pressure Relief
- Obtain the vehicle owners radio theft protection code prior to disconnecting the battery ground cable, if equipped.
- Disconnect the battery ground cable.
- Remove the fuel fill cap to release fuel tank pressure.
- On models less fuel filter service bolt, place a shop towel over the banjo bolt at top of fuel filter. Slowly loosen the banjo bolt one complete turn. When loosening the banjo bolt, use a backup wrench to hold the fuel filter in position.
- On m...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude FUEL FILTER REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
CV AXLE SHAFT, Replace -> Front
Vehicle: 1998 Honda Prelude SH 2.2 L4 GAS
Front
- Loosen wheel nuts slightly.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Drain transmission fluid and reinstall drain plug using a new washer.
- Lift up locking tab on spindle nut then remove nut.
- On models equipped with ATTS, remove cotter pin from radius rod ball joint castle nut and remove nut.
- Install 14 mm hex nut on ball joint and ensure nut is flush with ball joint pin end.
- Remove self-locking nut and flange bolts from dampner fork.
- Remove dampner fork.
- Remove cotter pin from radius rod ball joint c...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Alternator, Replace
Vehicle: 1998 Honda Prelude SH 2.2 L4 GAS
- Disconnect battery ground cable, then disconnect positive cable at battery.
- Remove power steering pump.
- Disconnect 4P connector from alternator.
- Remove terminal nut and BLK wire from B terminal.
- Remove mounting bolt, then adjustment locknu...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Honda -> Anti-Lock Brake System (ABS)/VSA System Warning Lamp -> 1997-2001 Prelude
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
The Anti-Lock warning lamp is used to warn of a system fault. The lamp monitors the condition of the anti-lock brake system. It will be lit during engine start-up, but should go off when the self-diagnostic system determines that the system is operating properly. If the lamp remains lit, a fault in the anti-lock brake system is indicated. After diagnosis and repair of the system, the lamp may be turned off as follows:
- Place ignition switch in Off position.
- Connect service connector 07PAZ-0010100, or equivalent, to service check connector, Fig...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Radiator, Replace
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
- Drain coolant into a suitable container.
- Disconnect radiator hoses and ATF cooler hoses, Figs. and .
- Disconnect fan motor electrical connectors, then remove r...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 1998 Honda Prelude AUTOMOBILES
Serpentine Drive Belt, Replace -> Alternator and Air Conditioning -> Power Steering
Vehicle: 1998 Honda Prelude 2.2 L4 GAS
Alternator and Air Conditioning
- Disconnect battery ground cable from battery.
- Loosen upper mounting bolt and lower alternator mounting nut.
- Loosen lower mounting bolt and lower alternator mounting nut.
- Remove A/C compressor drive and alternator drive belt.
- Clean and inspect belt surfaces ...
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 1998 Honda Prelude AUTOMOBILES
Component location diagrams for most 1998 Honda Prelude cars and light trucks sold in the U.S. from 1990+.
 Supplemental Restraint System Main Wiring Harness Connector Locations Diagram for 1998 Honda Prelude SH 2.2 L4 GASComponents on diagram: |
 ABS Component Locations Diagram for 1998 Honda Prelude 2.2 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 1998 Honda Prelude AUTOMOBILES
OEM drawn wiring diagrams for most 1998 Honda Prelude cars and light trucks sold in the U.S.
 1998 Honda Prelude SH 2.2 L4 GAS Wiring DiagramComponents on diagram: |
 1998 Honda Prelude SH 2.2 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 1998 Honda Prelude AUTOMOBILES
OEM TSB listings for most 1998 Honda Prelude cars and light trucks sold in the U.S. from 1985+.
|
Document: ATEQ VT55 TPMS Update Information Vehicle: 1998 Honda Prelude 2.2 L4 GAS Auto Systems: |
|
Document: ED-18 Battery Analyzer Update Information Vehicle: 1998 Honda Prelude 2.2 L4 GAS Auto Systems: |
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 1998 Honda Prelude AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 1998 Honda Prelude cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 1998 Honda Prelude cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 1998 Honda Prelude cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 1998 Honda Prelude cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 1998 Honda Prelude SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
