Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 1999 Chevrolet Corvette car and truck
repair procedures including Chevrolet engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 1999 Chevrolet Corvette automobile. Try the Automotix DIY solution today!
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> General Motors -> Brake System Bleed -> Bleed Sequence -> Hydraulic System Flush -> Manual -> Pressure
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
Manual
Pressure bleeding is recommended for all hydraulic systems. However, if a pressure bleeder is unavailable, use the following procedure. Brake fluid damages painted surfaces. Immediately clean any spilled fluid.
- Remove vacuum reserve by pumping brakes several times with engine off.
- Fill master cylinder reservoir with clean brake fluid. Do not let reservoir fall below half full during bleeding procedure.
- If required, bleed master cylinder as follows:
- Loosen master cylinder forward brake line connection until fluid flows from reservoir, then tighten brake line.
- Have assistant t...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> Description -> AC-Delco Single Diaphragm Type -> AC-Delco Tandem Diaphragm Type -> Toyota/GM Single Diaphragm Type
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
AC-Delco Tandem Diaphragm Type
This unit utilizes a vacuum power chamber, consisting of a front and rear shell, housing divider, front and rear diaphragm, plate assemblies, hydraulic pushrod and a diaphragm return spring, Fig. .
In normal operating mode, with service brakes in released position, the booster operates with vacuum on both sides of its diaphragms. When brakes are applied, air at atmospheric pressure is admitted to one side of each diaphragm to provide power assist. When the service brake is released, atmospheric air is shut off from one side of each diaphragm. The air is ...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Single Piston Rear Disc Brake -> Troubleshooting -> Brake Roughness
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
Brake Roughness
The most common cause of brake chatter on disc brakes is a variation in disc thickness. If roughness or vibration is encountered during highway operation or if pedal pulsation is experienced at low speeds, the disc may have excessive thickness variation. To inspect for this condition, measure the disc at 12 points with a micrometer at a radius approximately one inch from edge of disc. If thickness measurements vary by more than ...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Hydraulic Brake Systems -> General Motors -> Hydraulic Brake System Specifications
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Power Brake Units -> General Service
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
Two basic types of power assist mechanisms are used: vacuum assist diaphragm assemblies, which use engine vacuum or, in some cases vacuum pressure developed by an external vacuum pump. The second type is a hydraulic pressure assist mechanism, which use pressure developed by an external pump (usually the power steering pump). Both systems act to increase the force exerted on the master cylinder piston by the operator. This in turn increases the hydraulic pressure delivered to the wheel cylinders while decreasing driver effort required to obtain acceptable stopping performance.
Vac...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 1999 Chevrolet Corvette AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 1999 Chevrolet Corvette cars and light trucks from 1990+.
Disc Brakes -> PBR Dual Piston Front Disc Brake -> Precautions
Vehicle: 1999 Chevrolet Corvette 5.7 V8 GAS
- Grease or any other foreign material must be kept off brake linings, caliper, surfaces of disc and external surfaces of hub during service procedures.
- Handling brake disc and caliper should be done in a way to avoid deformation of disc and nicking or scratching brake linings.
- If inspection reveals worn or damaged rubber piston seals, they should be replaced.
- During removal and installation of a wheel assembly, ensure not to interfere with or dama...
CLICK HERE TO GET FULL ACCESS TO 1999 Chevrolet Corvette BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 1999 Chevrolet Corvette vehicle.
|
| Access the Complete guide! |
