Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2001 Hyundai Santa FE car and truck
repair procedures including Hyundai engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2001 Hyundai Santa FE automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2001 Hyundai Santa FE
- 2001 Hyundai Santa FE 2.4 L4 GAS, CC:2351, Fuel Injection
- 2001 Hyundai Santa FE 2.7 V6 GAS, CC:2656, Fuel Injection
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Anti-lock Brakes -> System Service -> 1997-98 -> 1999-2002 -> Accent -> Brake System Bleed -> Component Replacement -> Elantra, Sonata & Tiburon -> Electronic Control Unit (ECU) -> Front Wheel Sensors -> Hydraulic Control Unit (HCU) -> Modulator -> Rear Wheel Sensors
Vehicle: 2001 Hyundai Santa FE 2.7 V6 GAS
Brake System Bleed
- Bleed normal brake circuit using standard procedure as outlined in "Hydraulic Brake Service."
- Turn ignition switch Off, then connect MUT to diagnosis connector.
- Turn ignition switch to On position, but do not start engine. Multi-use tester should now be On.
- Follow each of the steps listed in Fig. for each bleed screw in order shown:
- Place a clear plastic bleeder tube on screw to be bled.
- Apply light and constant pressure to brake pedal.
- Use multi-use tester to actuate appropriate valve. As valve cycles, fluid and/or air will emerge from bleed screw and brake pedal will...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> Preliminary Inspection -> System Diagnosis Step Indicator Check
Vehicle: 2001 Hyundai Santa FE 2.7 V6 GAS
Preliminary Inspection
Start engine and drive at a speed of 3-6 mph, then verify that the modulator is operating by listening for motor pump hum and solenoid clicking for one or two seconds. Procedure should be performed within first three minutes after start up. Solenoid valve and motor pum...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Anti-lock Brakes -> Troubleshooting -> Preliminary Inspection -> System Diagnosis Step Indicator Check
Vehicle: 2001 Hyundai Santa FE 2.4 L4 GAS
Preliminary Inspection
Start engine and drive at a speed of 3-6 mph, then verify that the modulator is operating by listening for motor pump hum and solenoid clicking for one or two seconds. Procedure should be performed within first three minutes after start up. Solenoid valve and motor pum...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Drum Brakes -> Brake Service -> Accent, Elantra, Sonata & Tiburon -> Inspection -> Installation -> Removal -> Santa Fe
Vehicle: 2001 Hyundai Santa FE 2.7 V6 GAS
Removal
Accent, Elantra, Sonata & Tiburon
- Raise and support vehicle, then remove wheel/tire assembly.
- On Accent, Elantra and Tiburon models, remove axle nut, then the hub and drum assembly, Fig. .
- On Sonata models, remove brake drum. If drum is difficult to remove, screw in bolts to pull drum out, Figs. and .
- On all models, remove end shoe springs, cylinder and hold-down spring.
- Remove shoes and adjuster as an assembly.
Santa Fe
- Raise and support vehicle, then remove wheel/tire assembly.
- Remove brake drum Fig. .
- Remove brake shoe hold-down spring and strut.
- Remove brake shoe return springs...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Power Brake Units -> Power Brake Unit, Replace
Vehicle: 2001 Hyundai Santa FE 2.7 V6 GAS
- Remove master cylinder as outlined under "Component Replacement" in "Hydraulic Brake System."
- Disconnect vacuum hose.
- From inside vehicle, separate bra...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
BRAKE SERVICE PROCEDURES FOR 2001 Hyundai Santa FE AUTOMOBILES
Includes anti-lock brakes, disc, drum, power and hydraulic brake services diagnostics and procedures for domestic and imported 2001 Hyundai Santa FE cars and light trucks from 1990+.
Disc Brakes -> Brake Pad Service -> 1997-98 -> 1999-2002 -> Accent -> Elantra & Tiburon -> Elantra, Sonata & Tiburon -> Front -> Rear -> Santa Fe -> Sonata -> XG 300 & XG 350
Vehicle: 2001 Hyundai Santa FE 2.7 V6 GAS
Front
Accent
- Raise and support vehicle, then remove wheel/tire assembly.
- Remove lower bolt and caliper assembly, Fig. . Position assembly aside using suitable wire.
- Remove brake pads and shim.
- Bottom piston in caliper using a suitable tool.
- Install new brake pads and attach shim to the outer pad. Tighten lower bolt to specifications.
Elantra, Sonata & Tiburon
- Raise and support vehicle, then remove wheel/tire assembly.
- Remove two mounting bolts attaching caliper to torque plate, Fig. .
- Remove brake caliper assembly, then position aside using suitable wire.
- Remove brake pads.
- Install pad c...
CLICK HERE TO GET FULL ACCESS TO 2001 Hyundai Santa FE BRAKE SERVICE PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
