Auto Parts Search
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Mazda B4000 car and truck
repair procedures including Mazda engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your 2008 Mazda B4000 automobile. Try the Automotix DIY solution today!
We have info for following modifications of 2008 Mazda B4000
- 2008 Mazda B4000 4.0 V6 GAS, CC:4016, Fuel Injection, Engine VIN:, Desg:E
- 2008 Mazda B4000 SE 4.0 V6 GAS, CC:4016, Fuel Injection, Engine VIN:, Desg:E
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Mazda B4000 SE 4.0 V6 GAS
Front
- Place transmission in neutral, and raise and support vehicle.
- Mark front companion flange to front driveline.
- Mark transfer case companion flange to front driveline.
- Remove front driveline shaft to transfer case bolts and retainers.
- Remove front driveline shaft-to-front axle bolts.
- Remove driveline.
- Reverse procedure to install, noting the following:
- Torquefront driveline transfer case bolts to 13 ft. lbs.
Rear
- Place transmission...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
Disassemble
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Mark driveline components.
- Clamp u-joint using suitable tool in vise.
- Remove snap rings. If necessary, use a pair of pliers to remove bearing cup if it cannot be pressed out all the way.
- Remove driveshaft slip yoke.
- Position driveshaft slip yoke using suitable tool.
- Press out bearing cup.
- Rotate driveshaft slip yoke.
- Press spider to remove remaining bearing cup.
- Remove driveshaft slip yoke...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
- Ensure vehicle transmission is in neutral.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove hub nut and washer and discard. Do not allow disc brake caliper to suspend freely from brake hose. Support caliper using mechanics wire.
- Remove front disc brake caliper, anchor plate, and pads as an assembly and position assembly aside.
- Remove brake disc. Do not use a hammer to separate outboard CV joint from wheel hub. Damage to outboard CV joint stub shaft threads and internal CV joint components may result.
- Se...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
DRIVESHAFT, Replace -> Front -> Rear
Vehicle: 2008 Mazda B4000 SE 4.0 V6 GAS
Disassemble
- Place driveshaft on suitable workbench. Do not damage driveshaft when servicing on workbench. Ensure driveline and components are reference marked to prevent driveline imbalance.
- Mark driveline components.
- Clamp u-joint using suitable tool in vise.
- Remove snap rings. If necessary, use a pair of pliers to remove bearing cup if it cannot be pressed out all the way.
- Remove driveshaft slip yoke.
- Position driveshaft slip yoke using suitable tool.
- Press out bearing cup.
- Rotate driveshaft slip yoke.
- Press spider to remove remaining bearing cup.
- Remove driveshaft slip yoke...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
CV AXLE SHAFT, Replace
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
Front
- Place transmission in neutral, and raise and support vehicle.
- Mark front companion flange to front driveline.
- Mark transfer case companion flange to front driveline.
- Remove front driveline shaft to transfer case bolts and retainers.
- Remove front driveline shaft-to-front axle bolts.
- Remove driveline.
- Reverse procedure to install, noting the following:
- Torquefront driveline transfer case bolts to 13 ft. lbs.
Rear
- Place transmission...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2008 Mazda B4000 cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assembly -> Disassemble
Vehicle: 2008 Mazda B4000 SE 4.0 V6 GAS
- Ensure vehicle transmission is in neutral.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove hub nut and washer and discard. Do not allow disc brake caliper to suspend freely from brake hose. Support caliper using mechanics wire.
- Remove front disc brake caliper, anchor plate, and pads as an assembly and position assembly aside.
- Remove brake disc. Do not use a hammer to separate outboard CV joint from wheel hub. Damage to outboard CV joint stub shaft threads and internal CV joint components may result.
- Se...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
| More parts |
| Get the Complete Technical Service Bulletins! |
 Access diagrams and repair information such as wiring diagrams,
diagnosis and repair charts, manufacturer
service bulletins, and OEM Part
numbers of your 2008 Mazda B4000 vehicle.
|
| Access the Complete guide! |
