Auto Parts Search
2008 Mazda B4000 CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mazda REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
Front
- Place transmission in neutral, and raise and support vehicle.
- Mark front companion flange to front driveline.
- Mark transfer case companion flange to front driveline.
- Remove front driveline shaft to transfer case bolts and retainers.
- Remove front driveline shaft-to-front axle bolts.
- Remove driveline.
- Reverse procedure to install, noting the following:
- Torquefront driveline transfer case bolts to 13 ft. lbs.
Rear
- Place transmission...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Wiring Diagrams -> Wire Color Code Identification
Vehicle: 2008 Mazda B4000 SE 4.0 V6 GAS
Refer to Fig. for wiring...
[[table data]]CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Starter, Replace
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
- Position vehicle on lift and ensure transaxle is in neutral position.
- Disconnect battery ground cable.
- Raise vehicle on lift.
- Remove protective solenoid starter terminal cap. Ensure protective cap is installed over solenoid terminal when installing starter motor. Failure to follow this instruction may result in personal injury.
- Remove nut from starter cable B-terminal and disconnect wire connector from solenoid S-terminal.
- Remove stud bolt securing starter and pull downward on starter to...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 STARTER & ALTERNATOR REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Mazda -> Automatic Transaxle Warning Lamp ->
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
This lamp should light for approximately 6-8 seconds when the ignition is turned to On position as a bulb check. If the warning lamp flashes or lights, the tran...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Coolant Hose, Replace -> Lower -> Upper
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
Lower
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at radiator outlet.
- Remove hose from radiator.
- Reposition hose clamp at water inlet.
- Remove hose from water inlet.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Mazda B4000 AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Mazda B4000 4.0 V6 GAS
- Rotate or lift the belt tensioner arm, using a suitable tool to relieve tension from dr...
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Mazda B4000 AUTOMOBILES
Component location diagrams for most 2008 Mazda B4000 cars and light trucks sold in the U.S. from 1990+.
Rear Body Components Diagram for 2008 Mazda B4000 SE 4.0 V6 GAS Components on diagram: |
Engine Compartment Diagram for 2008 Mazda B4000 4.0 V6 GAS Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Mazda B4000 AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Mazda B4000 cars and light trucks sold in the U.S.
2008 Mazda B4000 SE 4.0 V6 GAS Wiring Diagram Components on diagram: |
2008 Mazda B4000 4.0 V6 GAS Wiring Diagram Components on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Mazda B4000 AUTOMOBILES
OEM TSB listings for most 2008 Mazda B4000 cars and light trucks sold in the U.S. from 1985+.
Document: ENGINE CAUTION FOR NEW VEHICLE STORAGE Vehicle: 2008 Mazda B4000 4.0 V6 GAS Auto Systems: |
Document: GRABBING CONDITION FROM REAR DRUM BRAKES Vehicle: 2008 Mazda B4000 4.0 V6 GAS Symptoms: |
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Mazda B4000 AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Mazda B4000 cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Mazda B4000 cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Mazda B4000 cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Mazda B4000 cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Mazda B4000 SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2008 Mazda B4000 vehicle. |
Access the Complete guide! |