Auto Parts Search
We have info for following modifications of 2009 Suzuki Grand Vitara
- 2009 Suzuki Grand Vitara 2.4 L4 GAS, CC:2393, Fuel Injection, Engine VIN:, Desg:0
- 2009 Suzuki Grand Vitara Luxury 3.2 V6 GAS, CC:3195, Fuel Injection, Engine VIN:, Desg:1
- 2009 Suzuki Grand Vitara Luxury 2.4 L4 GAS, CC:2393, Fuel Injection, Engine VIN:, Desg:0
- 2009 Suzuki Grand Vitara Xsport 3.2 V6 GAS, CC:3195, Fuel Injection, Engine VIN:, Desg:1
- 2009 Suzuki Grand Vitara Xsport 2.4 L4 GAS, CC:2393, Fuel Injection, Engine VIN:, Desg:0
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2009 Suzuki Grand Vitara 2.4 L4 GAS
Disassemble
- Place match marks on flange yoke and shaft.
- Using snap ring plier, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 3 and 4.
- Push out bearing race on flange yoke side as described in Step 2 and 3, and then, holding bearing race in a vise, tap flange yoke and take out race.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2009 Suzuki Grand Vitara Xsport 2.4 L4 GAS
Disassemble
- Place match marks on flange yoke and shaft.
- Using snap ring plier, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 3 and 4.
- Push out bearing race on flange yoke side as described in Step 2 and 3, and then, holding bearing race in a vise, tap flange yoke and take out race.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2009 Suzuki Grand Vitara Xsport 3.2 V6 GAS
Front
- Undo staking and remove drive shaft nut.
- Raise and support vehicle, then remove wheel.
- Drain front differential oil into a suitable container.
- Disconnect tie-rod end from steering knuckle.
- Remove stabilizer joint from stabilizer bar.
- Remove brake hose mounting bolt.
- Remove suspension control arm.
- Remove front drive shaft flange nuts.
- Remove drive shaft assembly from front differential.
- Reverse procedure to install, noting the following:
- Torque drive shaft nut to 159 ft. lbs.
- Torque flange nuts to 58 ft. lbs.
- Torq...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2009 Suzuki Grand Vitara 2.4 L4 GAS
Front
- Undo staking and remove drive shaft nut.
- Raise and support vehicle, then remove wheel.
- Drain front differential oil into a suitable container.
- Disconnect tie-rod end from steering knuckle.
- Remove stabilizer joint from stabilizer bar.
- Remove brake hose mounting bolt.
- Remove suspension control arm.
- Remove front drive shaft flange nuts.
- Remove drive shaft assembly from front differential.
- Reverse procedure to install, noting the following:
- Torque drive shaft nut to 159 ft. lbs.
- Torque flange nuts to 58 ft. lbs.
- Torq...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
DRIVESHAFT U-JOINT, Replace -> Assemble -> Disassemble
Vehicle: 2009 Suzuki Grand Vitara Luxury 2.4 L4 GAS
Disassemble
- Place match marks on flange yoke and shaft.
- Using snap ring plier, remove 2 circlips.
- Using special tool 09926-48010 or equivalent, push spider bearing race out 0.12 - 0.16 in. from shaft yoke race. Before pushing it out, apply penetrate lubricant between bearing race and yoke race.
- Tapping yoke with a hammer, completely remove bearing race.
- Take out bearing race on other side in same way as in Step 3 and 4.
- Push out bearing race on flange yoke side as described in Step 2 and 3, and then, holding bearing race in a vise, tap flange yoke and take out race.
- Remove ...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2009 Suzuki Grand Vitara AUTOMOBILES
Includes CV axle, universal joint, and driveline replacement, for domestic and imported 2009 Suzuki Grand Vitara cars and light trucks from 1990+.
CV AXLE SHAFT, Replace -> Front -> Rear
Vehicle: 2009 Suzuki Grand Vitara Luxury 2.4 L4 GAS
Front
- Undo staking and remove drive shaft nut.
- Raise and support vehicle, then remove wheel.
- Drain front differential oil into a suitable container.
- Disconnect tie-rod end from steering knuckle.
- Remove stabilizer joint from stabilizer bar.
- Remove brake hose mounting bolt.
- Remove suspension control arm.
- Remove front drive shaft flange nuts.
- Remove drive shaft assembly from front differential.
- Reverse procedure to install, noting the following:
- Torque drive shaft nut to 159 ft. lbs.
- Torque flange nuts to 58 ft. lbs.
- Torq...
CLICK HERE TO GET FULL ACCESS TO 2009 Suzuki Grand Vitara DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
Shop online for auto body parts, engines, wheels, lights...
More parts |
Get the Complete Technical Service Bulletins! |
Access diagrams and repair information such as wiring diagrams, diagnosis and repair charts, manufacturer service bulletins, and OEM Part numbers of your 2009 Suzuki Grand Vitara vehicle. |
Access the Complete guide! |