Auto Parts Search
2008 Mitsubishi Lancer CAR/TRUCK REPAIR PROCEDURES AND DIAGRAMS - WHAT Mitsubishi REPAIR SHOPS DON'T WANT YOU TO KNOW
Learn how to repair a car or truck, install or remove parts, wire an engine, reset warning lights, replace fuel filter, fix auto body and more. Get Automotix DIY!Select Section
- Component Locations
- Wiring Diagrams
- Technical Service Bulletins
- Specifications
- Driveline, U-Joint & CV Axles Replacement
- Tire Pressure Monitoring System
- Starter & Alternator Replacement
- Cabin Air Filter Locations & Replacement
- Maintenance Lamp Reset
- Radiator & Hose Replacement
- Serpentine Belt Service
Automotix DIY provides automotive consumers and do it yourselfers; the most comprehensive repair information about 2008 Mitsubishi Lancer car and truck
repair procedures including Mitsubishi engine diagrams, wiring diagrams, repair work estimating measures, technical service bulletins, auto body work
guidance, starter & alternator replacement procedures, serpentine belt replacement procedures, radiator & hose replacement procedures, tune-up &
drivability specifications, quick lube illustrations, preventive maintenance guide, engine light reset instructions, parts removal and install
procedures, fuel filter replacement directions, component location diagrams, air filter locations & replacement instructions, a/c
system specifications, and general auto service procedures. You don't have to be a car mechanic or technician to know how to fix
your Mitsubishi Lancer automobile. Try the Automotix DIY solution today!
DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
CV AXLE SHAFT, Replace
Vehicle: 2008 Mitsubishi Lancer Evolution GSR 2.0 L4 GAS
Do not strike ABS rotors or outer race of driveshaft against other parts when removing or installing driveshaft. Use care not to strike pole piece at tip of front wheel speed sensor with tools when servicing vehicle.
- Raise and support vehicle and support it with safety stands in proper locations.
- Remove wheel nuts and front wheels.
- Remove wheel hub cotter pin, nut, and washer. Do not apply pressure to wheel bearing from vehicle weight to avoid possible damage when driveshaft nut is loosened.
- On models equipped with ABS, remove bolt from front ABS wheel sensor bracket.
- On all ...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer DRIVELINE, U-JOINT & CV AXLES REPLACEMENT PROCEDURES
TIRE PRESSURE MONITORING SYSTEM PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Diagnosis & Testing -> Accessing Diagnostic Trouble Codes -> Clearing Diagnostic Trouble Codes -> Diagnostic Trouble Code Interpretation -> Troubleshooting
Vehicle: 2008 Mitsubishi Lancer GTS 2.0 L4 GAS
Accessing Diagnostic Trouble Codes
Connect a suitable scan tool to vehicle data link connector, Fig. and follow scan tool manufacturer's instructions.
Diagnostic Trouble Code Interpretation
[[table data]]Clearing Diagnostic Trouble Codes
Connect a suitable scan tool to vehicle data link connector, Fig. and follow scan tool manufacturer's instructions.
Troubleshooting
If the TPMS warning light is on, ensure tire pressure is within specifications. If a tire being used does not contain a TPMS transmitter, such as a spare tire, the TPMS warning lamp will flash and the TPMS will not function corre...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer TIRE PRESSURE MONITORING SYSTEM PROCEDURES
STARTER & ALTERNATOR REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Starter, Replace
Vehicle: 2008 Mitsubishi Lancer Evolution GSR 2.0 L4 GAS
- Disconnect battery cables.
- Remove retainer securing air duct then remove duct.
- Remove nut from starter cable B+ terminal and disconnect wire connector from solenoid S-terminal.
- Remove bolts securing starter motor, gr...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer STARTER & ALTERNATOR REPLACEMENT PROCEDURES
CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Cabin Air Filter Service -> Mitsubishi -> Lancer & 2003-06 Outlander
Vehicle: 2008 Mitsubishi Lancer Evolution MR 2.0 L4 GAS
Under normal operating conditions the cabin air filter should be replaced every 15,000 miles. In dusty areas change the cabin air filter more often.
- Open the glove compartment.
- Remove the glove compartment stops, then the glove compartment.
- Remove the two screws securing the cabin air filter cover, the cover.
- Remove the ...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer CABIN AIR FILTER LOCATIONS & REPLACEMENT PROCEDURES
MAINTENANCE LAMP RESET PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Mitsubishi -> Tire Pressure Monitoring System (TPMS) Warning Indicator -> 2008-09 Lancer & Lancer Evolution -> Relearn -> Reset -> Tire Pressure Sensor ID Registration -> Warning Lamp
Vehicle: 2008 Mitsubishi Lancer Evolution GSR 2.0 L4 GAS
Reset
Tire Pressure Sensor ID Registration
- Connect a suitable scan tool to vehicle data link connector, Fig. .
- Follow scan tool instructions to enter "Tire Pressure Sensor ID Registration" mode.
- Select the number of tires that you want to register.
- Starting at any TPMS transmitter, emit a signal from the transmitter as follows:
- Decrease the tire pressure to 25.2 psi or less by changing 2.9 psi or more, and register the TPMS transmitter ID code of each wheel to TPMS receiver
- Verify that a signal has been received by the TPMS rec...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer MAINTENANCE LAMP RESET PROCEDURES
RADIATOR & HOSE REPLACEMENT PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Heater Hose, Replace -> Inlet -> Outlet
Vehicle: 2008 Mitsubishi Lancer ES 2.0 L4 GAS
Inlet
- Disconnect battery ground cable.
- Drain cooling system into a suitable container by loosening drain plug of radiator.
- Reposition hose clamp at heater core.
- Remove hose from heater core.
- Reposition hose clamp at thermostat case.
- Remove hose from thermostat case.
- Remove hose from vehicle.
- Reverse procedure t...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer RADIATOR & HOSE REPLACEMENT PROCEDURES
SERPENTINE BELT SERVICE PROCEDURES FOR 2008 Mitsubishi Lancer AUTOMOBILES
Serpentine Drive Belt, Replace
Vehicle: 2008 Mitsubishi Lancer DE 2.0 L4 GAS
- Raise and support vehicle.
- Remove both side and rear engine under covers.
- Remove radiator condenser tank mounting bolts using a suitable tool and move radiator condenser tank aside.
- Rotate p...
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer SERPENTINE BELT SERVICE PROCEDURES
COMPONENT LOCATION DIAGRAMS FOR 2008 Mitsubishi Lancer AUTOMOBILES
Component location diagrams for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. from 1990+.
 Console Components Diagram for 2008 Mitsubishi Lancer Evolution MR 2.0 L4 GASComponents on diagram: |
 Engine Compartment Components Diagram for 2008 Mitsubishi Lancer ES 2.0 L4 GASComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer PARTS/COMPONENTS LOCATION DIAGRAMS!
WIRING DIAGRAMS FOR 2008 Mitsubishi Lancer AUTOMOBILES
OEM drawn wiring diagrams for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S.
 2008 Mitsubishi Lancer ES 2.0 L4 GAS Wiring DiagramComponents on diagram: |
 2008 Mitsubishi Lancer Evolution MR 2.0 L4 GAS Wiring DiagramComponents on diagram: |
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer WIRING DIAGRAMS!
TECHNICAL SERVICE BULLETINS FOR 2008 Mitsubishi Lancer AUTOMOBILES
OEM TSB listings for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. from 1985+.
|
Document: CRANKSHAFT OIL JOURNAL CLEARANCE SPECIFICATIONS - SERVICE MANUAL REVISION Vehicle: 2008 Mitsubishi Lancer Evolution MR 2.0 L4 GAS Auto Systems: |
|
Document: RKE INTEGRATED KEY CASE SERVICE PARTS KIT AVAILABILITY Vehicle: 2008 Mitsubishi Lancer Evolution MR 2.0 L4 GAS |
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer TECHNICAL SERVICE BULLETINS!
COMPONENT/PARTS SPECIFICATIONS FOR 2008 Mitsubishi Lancer AUTOMOBILES
BRAKE SPECIFICATIONS: Brake drum, rotor, caliper, and related specifications for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. and Canada from 1970+.
- Brake caliper mounting bolt torque
- Brake drum runout, machining, & discard specs
- Minimum brake lining thickness.
- Brake rotor runout, parallelism, machining, discard, & finish specs
A/C SYSTEM SPECIFICATIONS: Air conditioning refrigerant capacity and type as well as lubricant capacity for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. and Canada from 1980+.
- Refrigerant capacity & type, compressor oil viscosity, total system oil capacity & compressor clutch gap
COOLING SYSTEM BLEED: Cooling system bleeder valve identification, bleeder type and bleed procedures for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1986+.
PREVENTIVE MAINTENANCE: Preventive maintenance recommendations and required services for most domestic and imported cars and light trucks sold in the U.S. and Canada from 1980+. Includes severe and routine service schedules
QUICK-LUBE and ILLUSTRATIONS: Fluid recommendations, capacities, drain plug torques, tire data, and severe service recommended preventive maintenance schedules. Information covers most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. and Canada from 1980+. Engine and chassis service images.
- Automatic transmission/transaxles capacities, lubricant recommendations
- Differential/final drive capacities, lube recommendations, grades, & viscosities
- Final drive fill & drain plug torques
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Manual transmission/transaxle capacities, lube recommendations, grades, & viscosities
- Number of lubrication fittings & plugs
- Power steering, brake, & clutch fluid recommendations
- Engine oil capacities, API grade recommendations, SAE viscosity recommendations, drain plug torque
- Severe service maintenance & interval recommendations
- Tire sizes, wheel nut/bolt torque, pressures & rim sizes
- Transfer case capacities, lube recommendations, grades, & viscosities
TUNE-UP & DRIVEABILITY SPECIFICATIONS: Most tune-up specifications for most 2008 Mitsubishi Lancer cars and light trucks sold in the U.S. and Canada from 1980+
- Airflow sensor electrical specifications
- Tensioning specifications for systems with automatic tensioners
- Barometric pressure sensor specs
- Battery group number and cranking performance
- Crankshaft & camshaft position sensor resistance
- Engine compression pressures
- Coolant temperature sensor specs
- Computer advance.
- Diesel fuel temperature sensor resistance.
- Distributor advance specifications
- Ignition pickup coil resistance
- Exhaust gas recirculation temperature sensor resistance
- Engine fastener torque values
- Firing order diagrams
- Fuel system pressures
- Generator (alternator) specs
- Intake air temperature sensor specs
- Ignition coil specifications
- Fuel injector resistance
- Engine idle speeds
- Knock sensor resistance
- Manifold absolute pressure sensor specs
- Mixture control solenoid resistance
- Voltage regulator specs
- Spark plug applications & gaps
- Starter motor electrical specs.
- Tensioning specifications for systems without automatic tensioners
- Throttle body temperature sensor resistance
- Ignition timing in degrees at rpm
- Transmission oil temperature sensor resistance
- Throttle position sensor specs
- Vacuum sensor valve specs
CLICK HERE TO GET FULL ACCESS TO 2008 Mitsubishi Lancer SPECIFICATIONS DATA!
Shop online for auto body parts, engines, wheels, lights...
| More parts |
